I’ve been living with a flatmate who’s been living on the couch for three years now.
It’s a really nice sofa bed, but it’s also made out of a cheap fabric.
I’ve never used a washable bed before, so I’ve had to make my own.
I found out the hard way that you can’t just throw a cheap bed away.
It can actually make a huge difference to the quality of your home.
So I decided to take a chance and try my hand at a wash-able sofa.
I’m going to explain how to make one myself, and how I’ve made mine look as good as the ones I’ve seen in magazines.
So, without further ado, let’s make one.
The Basics of a Washable Bed How to Make a Wash-able Bed You need: 2 x 2.5cm x 2cm (or 2 x 4cm x 4.5 cm) sheet of fabric or sheet fabric (you could use a fabric sprayer if you want to do this), a plastic sheet for the mattress, a fabric brush or a towel (if you don’t have a wash machine), and some sewing machines.
You’ll need to make sure you get your fabric from the store.
I bought some sheet fabric from a local fabric store.
You’ll need a couple of things to make a wash bed: a mattress fabric that has a fabric tag that says washable, a wash tag, and a sheet fabric with a wash label that says a fabric with washable tag.
These are usually sold in a kit of 3-4, but you can make your own by buying individual sheets of fabric and cutting the fabric to the desired length.
Find the tag you want and use the fabric sprayers you already have, to get it into the wash bed.
Cut out the tag that has the tag, leaving a 3cm wide piece of fabric.
Lay the tag flat on the fabric sheet, making sure that it’s not too high up in the fabric.
Repeat for all the other tags on the sheet, including the one with the wash label.
If you don’ want to buy tags, you can also buy tags at the fabric store (or get them from the fabric department of the store).
You can find a list of fabric store brands and tags here.
Put the fabric in the wash machine, and gently press it down.
It should look like this: The fabric should be completely dry now, but there may be some lint stuck to the top, or the fabric may have a small amount of lint on the top.
You can also see a few spots of lints on the side of the bed.
You might want to use a little rubbing alcohol to make it easier.
If it’s still too wet, gently press down again.
It shouldn’t come up to the surface anymore, but if it does, gently rub it back down again until it’s dry.
Now you’re ready to get to work.
When you’re done, you’ll have a bed with a clean wash label on it.
Take the fabric out of the wash bag and let it dry.
You could also use a cloth and press it on the surface of the mattress.
It might help to leave a little extra room on the bed, since you can see where the fabric was pressed.
If your bed has a wash bag, you might want another piece of cloth or a small paintbrush to paint on the wash tag.
If not, it’s probably fine to just keep the tag in the bag, just in case.
Next, take your fabric brush and gently brush off all the lint that may have been on the mattress tag.
Don’t worry about any of the other lint in the bed now, it should be very fine.
You don’t need to worry about lint sticking to your mattress.
Just clean the mattress fabric and remove the tag from the bed to the bottom of the bag.
If the tag is still sticky, you probably need to gently brush it off a bit more.
This will remove all the excess lint from the mattress and help the fabric dry.
Next, carefully fold the fabric around the tag.
Don’t forget to fold it all the way around.
If it’s a very long piece of the fabric, you may want to cut it into smaller pieces, just to get the tag out.
It will take a little bit of cutting to get all the fabric together, so be careful.
I didn’t cut it exactly in the middle, but in the center I folded the fabric all the right way, and it was really easy.
When you’re finished, you will have a nice, clean wash tag on the back of the dresser.
Now, you just need to take your clothes out of your bed, put them on, and take a look at the bed in the mirror.
If there’s any